Gallanthorn the Hero, goat head - Mythic Legions 1.0 scale

***PLEASE NOTE*** Action figure scales vary widely. We try to hit the Classified 1/12 and the McF/Mythic 1.0 scales. Please use photo references with figures for sizing. You are responsible for choosing the best size pieces for your figure. Js Armory does not accept returns for mistakes in size. IF you are in doubt if it will fit, please send us a message and we will assist you in your purchase. Th

Gallanthorn the Hero, goat head - Mythic Legions 1.0 scale

Designed by Jason Demon Rodriguez

NO FIGURES ARE INCLUDED. ONLY THE LISTED ITEMS

Disclaimers and Instructions:

This item is a 3d printed item for adults.  This is not intended for children.

Unpainted 3d items are very susceptible to UV light until they are coated with either a clear coat or paint. Please remember to protect it from sunlight until finished.

All items are made and/or painted by hand. There will be differences and imperfections in each piece. I strive to make quality items. Please understand that these are more fragile than a manufactured item. Please handle them with care. Most items have been coated with a primer that seals the item and may be minimally painted. The intention for my products is for the customizer to utilize and for the items to be further painted and detailed.

If you purchase pre-painted items, the paint may cause the item to be more rigid. You may need to heat items and shape them to your liking. Most vests will need this to fit properly and fasten onto a figure. Once in place, I recommend gluing the connectors.

All heads will need to be fit to your chosen body. Dremeling, putty, etc. will be needed to ensure a proper fit. I use a method that utilizes hot glue. Use petroleum jelly on the neck peg. Fill the head hole with enough glue to push the peg into the head and some of the glue to squeeze around the neck ball. As it dries, continue to move the neck peg so it will not bind in the hole.

Thank you so much for considering a purchase!

All hand-painted items present the chance of paint rub. Either the paint off the item or the paint off the item onto the figure. This isn't very common with the finish I use, but it has happened. Please handle the items with care. If placing a vest onto a figure and it needs to be shaped first, please warm it slowly with a hair dryer. Thank you!

***PLEASE NOTE*** Action figure scales vary widely. We try to hit the GI Joe Modern Era 1/18, Classified 1/12 and the McF/Mythic 1.0 scales. Please use photo references with figures for sizing. You are responsible for choosing the best size pieces for your figure. Js Armory does not accept returns for mistakes in size. IF you are in doubt if it will fit, please send us a message and we will assist you in your purchase.

Thank you!

ank you. ****READ ABOVE**** Gallanthorn the hero Goat head for 1.0 Mythic Legions Printed in Resione M70/TH72 or TH72 Color may vary Designed by Jason Demon 3d Studios https://www.instagram.com/jason_demon_3d_studio/ The ( ) Signifies a JsArmory Part Bin Location The heads are sized to pop on Mythic Legions 1.0, if you want to use it on a different neck, please refer to the instructions below. Heads will need to be fitted for the figure you choose. You can get away with sticky tack on the ball peg but a more permanent solution is best. Dremeling, putty, etc may be needed to ensure a proper fit. I use a method that utilizes hot glue. Use petroleum jelly on the neck peg. Fill the head hole with enough glue to push the peg into the head and some of the glue to squeeze around the neck ball. As it dries, continue to move the neck peg so it will not bind in the hole. NO FIGURES ARE INCLUDED. ONLY THE HEAD. There will be differences and imperfections in each piece including small flaws in prints. I strive to make quality items. Please understand that these are more fragile than a manufactured item. Please handle them with care. Thank you so much for considering a purchase! All hand-painted items present the chance of paint rub. Either the paint off the item or the paint off the item onto the figure. This isn't very common with the finish I use, but it has happened. Please handle the items with care. If placing a vest onto a figure and it needs to be shaped first, please warm it slowly with a hair dryer. Thank you!